Loflin Open-Front Skid Steer Brush Cutter | 60" & 72"

• Open-front deck provides aggressive entry into standing brush and overgrowth
• Available in 60" and 72" cutting widths
• Low-flow and high-flow motor configurations available
• Two-, three-, and four-blade configurations depending on cutter width
• Proprietary direct-drive system eliminates the gearbox and shear pins
• One-piece heat-treated forged steel drive axle
• Fully enclosed motor and drive assembly
• Reinforced 1/4" steel deck
• One-piece forged, fully heat-treated bi-directional blades
• Bi-directional cutting rotation
• Two oversized grease-packed tapered roller bearings
• Wire-protected lower grease seal
• Parker hydraulic hoses, fittings, and flat-face couplers
• Reinforced universal skid-steer quick-attach
• Industrial powder-coat finish
• Built in the USA

Cutting Widths: 60" and 72"
Deck Style: Open Front
Deck Thickness: 1/4" Reinforced Steel
Drive Type: Proprietary Direct Drive
Drive Axle: One-Piece Heat-Treated Forged Steel
Motor Type: Geroler Hydraulic Motor
Hydraulic Flow Range: 12–43 GPM, Depending on Configuration
Rotation: Bi-Directional
Blades: One-Piece Forged, Fully Heat-Treated and Bi-Directional
Blade Configurations: 2, 3 or 4 Blades, Depending on Width
Bearings: Two Oversized Grease-Packed Tapered Roller Bearings
Lower Seal: Wire-Protected Grease Seal
Motor Protection: Fully Enclosed
Hydraulic Components: Parker Hoses, Fittings and Flat-Face Couplers
Mounting Interface: Reinforced Universal Skid-Steer Quick Attach
Machine Type: Full-Size Skid Steers and Compact Track Loaders
Finish: Industrial Powder Coat
Country of Manufacture: USA

The hydraulic motor must be matched to the machine’s actual auxiliary hydraulic flow.

60" MOTOR OPTIONS

80cc Motor: 12–17 GPM
100cc Motor: 15–22 GPM
125cc Motor: 21–28 GPM
160cc Motor: 28–34 GPM
200cc Motor: 35–43 GPM


72" MOTOR OPTIONS

100cc Motor: 14–18 GPM
125cc Motor: 16–23 GPM
160cc Motor: 16–28 GPM
200cc Motor: 28–34 GPM
250cc Motor: 35–43 GPM


Flow ranges overlap. A larger motor is not automatically better. Final motor selection depends on actual hydraulic flow, operating pressure, machine capacity, and application.

CrewTough will verify hydraulic compatibility before the attachment is released.

2 Blades: Lighter rotating assembly and a good choice for general brush cutting where maximum blade count is not needed.

3 Blades: Provides more blade contact per rotation and is a strong all-around choice for frequent land clearing and brush reduction.

4 Blades: Available on the 72" model for more blade contact and material processing. It also adds weight and rotating mass, so machine and hydraulic compatibility must be verified.

Shipping Incl. to lower 48.
Hawaii & Alaska email Support@CrewTough.com

This attachment is covered by the applicable Loflin Fabrication manufacturer warranty against defects in materials and workmanship.

Warranty coverage does not include normal wear, cutting blades, teeth, hoses, hydraulic fittings, damage caused by misuse, improper hydraulic flow or pressure, incorrect installation, inadequate maintenance, unauthorized modifications, or use outside the attachment’s intended application.

Machine compatibility and hydraulic requirements must be confirmed before ordering. Damage caused by operating the brush cutter with an incompatible machine or incorrect hydraulic setup is not covered.

If you experience an issue, contact CrewTough with your order number, machine information, photos, and a description of the problem. CrewTough will work with Loflin Fabrication to review the claim and coordinate approved warranty service or replacement parts.

Returns require prior authorization. Because this product is heavy, freight-shipped, and may be built or configured for a specific order, cancellations and returns may be limited and may be subject to restocking and return-freight charges. Used, installed, damaged, or special-order products cannot be returned unless approved as part of a valid warranty claim.